NEW FINISHING PASS DESIGN FOR ROLLING HEXAGON BARSPOSTONOGOV YU A; NIKIFOROV VV.1980; METALLURG; SUN; DA. 1980-08; VOL. 25; NO 8; PP. 28-29Article

TEMPERATURE STABILITY DURING HOT ROLLING OF WIDE STRIPVOROBEI SA; MAZUR VL.1982; STAL; ISSN 0038-920X; SUN; DA. 1982-08; VOL. 52; NO 8; PP. 52-55; BIBL. 4 REF.Article

MECHANICAL AND STRUCTURAL PROPERTIES OF STRIP FOR TINPLATE PRODUCTIONJONKOVA Y; MINCHEVA V; MARINOV A et al.1982; METALURGIYA; ISSN 0543-5838; BGR; DA. 1982-06; VOL. 37; NO 6; PP. 6-9; BIBL. 3 REF.Article

SCHLEUDERGEGOSSENE PLATINEN AUS MOLYBDAENSCHNELLSTAEHLEN = CENTRIFUGAL CAST SHEET BAR FROM MOLYBDENUM HIGH-SPEED STEELSBARTOS J; KOSAN J; SOUSTEK M et al.1979; FREIBERG. FORSCHUNGSH., REIHE B; DDR; DA. 1979; VOL. 112; PP. 125-137; BIBL. 11 REF.Conference Paper

Développement d'un modèle mathématique pour le module élastique d'un laminoir finisseur continu à chaud = Mathematical model for the elastic modulus of a continuous finishing hot millCAMURRI, C-P; PINTO, P. A; PARADA, M. A et al.Revue de métallurgie (Paris). 1985, Vol 82, Num 6, pp 459-464, issn 0035-1563Article

GRAIN REFINEMENT AND PROPERTIES OF PLAIN LOW CARBON STEEL IN THE CONTROLLED ROLLING PROCESSCUI WENXUA N; LI WENQIN G; DAI PINGUAN G et al.1981; IRON STEEL; CHN; DA. 1981-04; VOL. 16; NO 4; PP. 34-42; BIBL. 12 REF.Article

ANALYSIS OF SLAB TEMPERATURE CHANGE AND ROLLING MILL LINE LENGTH IN QUASI CONTINUOUS HOT STRIP MILL EQUIPPED WITH TWO ROUGHING MILLS AND SIX FINISHING MILLSHATTA N; KOKADO J; NISHIMURA H et al.1981; TRANS. IRON STEEL INST. JPN.; JPN; DA. 1981-04; VOL. 21; NO 4; PP. 270-277; BIBL. 6 REF.Article

STANOVENI SOUCINITELE PRESTUPU TEPLA PRI RIZENEM OCHLAZOVANI KRUHOVE OCELI = DIE BESTIMMUNG DES WAERMEUEBERGANGSFAKTORS BEI TEMPERATURGESTEUERTER ABKUEHLUNG VON RUNDSTAHLEN. = ESTABLISHING HEAT TRANSFER COEFFICIENT IN CONTROL COOLING OF ROUNDSDROZD V; POKLUDA L; BITTNER V et al.1981; HUTN. LISTY; CSK; DA. 1981-08; VOL. 36; NO 8; PP. 572-575; BIBL. 3 REF.Article

VERBESSERUNG DES VERFAHRENS ZUR ERZEUGUNG VON KALTGEWALZTEM TIEFZIEHBLECH FUER DIE AUTOMOBILINDUSTRIEFU ZUOBA O.1982; IRON STEEL; CHN; DA. 1982-09; VOL. 17; NO 9; PP. 25-29, 44; BIBL. 4 REF.Article

COOLING OF STRIPS BETWEEN THE STANDS OF WIDE STRIP FINISHING MILLDRUZHININ NN; GERTSEV AI; DRUZHININ AN et al.1980; STAL'; SUN; DA. 1980-07; VOL. 40; NO 7; PP. 596-599; BIBL. 3 REF.Article

GRAIN REFINEMENT AND PROPERTIES OF PLAIN LOW CARBON STEEL IN THE CONTROLLED ROLLING PROCESSCUI WENXUA N; LI WENQIN G; DAI PINGUAN G et al.1981; IRON STEEL; CHN; DA. 1981-04; VOL. 16; NO 4; PP. 34-42; BIBL. 12 REF.Article

THE RELATIONSHIP BETWEEN ACCELERATION AND THE CONTROL OF FINAL TEMPERATURE OF HOT STRIP MILLLI SONGTAN G; GE RUZHEN G.1981; IRON STEEL; CHN; DA. 1981-06; VOL. 16; NO 6; PP. 36-41Article

ANALYSIS OF SLAB TEMPERATURE CHANGE AND ROLLING MILL LINE LENGTH IN QUASI CONTINUOUS HOT STRIP MILL EQUIPPED WITH TWO ROUGHING MILLS AND SIX FINISHING MILLSHATTA N; KOKADO J; NISHIMURA H et al.1981; TRANS. IRON STEEL INST. JPN.; JPN; DA. 1981-04; VOL. 21; NO 4; PP. 270-277; BIBL. 6 REF.Article

Untersuchung der Umformverhaeltnisse sowie des Walzens von Profilen in Walzbloecken = Studies of the forming proportions and of the rolling of bars and sections in no-twist finishing-roll-blocksKUTZSCHE, K.Neue Hütte. 1985, Vol 30, Num 11, issn 0028-3207, 432Article

HOT STEEL STRIP FLATNESS BEING MEASURED BY NON-CONTACT SYSTEM AT DOMNARVET WORKS1981; IND. HEAT.; USA; DA. 1981-10; VOL. 48; NO 10; PP. 36, 38Article

LEISTUNGSFAEHIGE DRAHTFERTIGBLOECKE FUER HOHE AUSLAUFGESCHWINDIGKEITEN = EFFICIENT WIRE FINISHING BLOCKS FOR HIGH RUN-OUT SPEEDSBIERNOT O; MARZINKEWITSCH RA.1980; DRAHT-WELT; DEU; DA. 1980-10; VOL. 66; NO 10; PP. 402-404Article

ANALYSE DER UNEBENHEIT VON WARMBAND NACH DEM KUEHLENYOSHIDA H; SASAKI T; TANAKA T et al.1982; TETSU TO HAGANE; JPN; DA. 1982-06; VOL. 68; NO 8; PP. 965-973; BIBL. 24 REF.Article

EFFECT OF HOT ROLLING PROCESS ON DEEP DRAWABILITY AND RIDGING TENDENCY OF TI STABILIZED 17 CR STAINLESS STEELNAKAGAWA Y; SAKAMOTO T; YAMAUCHI I et al.1980; TETSU TO HAGANE; JPN; DA. 1980-05; VOL. 66; NO 6; PP. 657-666; BIBL. 29 REF.Article

VLIV PODMINEK VALCOVANI NA MECHANICKE VLASTNOSTI OCELI 11523 MIKROLEGOVANE TITANEM = INFLUENCE OF ROLLING CONDITIONS ON THE MECHANICAL PROPERTIES OF STEEL 11 523 MICROALLOYED WITH TITANIUMMAZANCOVA E; HYSPECKA L.1981; KOVOVE MATER.; CSK; DA. 1981-06; VOL. 19; NO 3; PP. 269-278; BIBL. 11 REF.Article

VLIV PODMINEK VALCOVANI NA MECHANICKE VLASTNOSTI OCELI 11523 MIKROLEGOVANE TITANEM = INFLUENCE OF ROLLING CONDITIONS ON THE MECHANICAL PROPERTIES OF STEEL 11 523 MICROALLOYED WITH TITANIUMMAZANCOVA E; HYSPECKA L.1981; KOVOVE MATER.; CSK; DA. 1981-06; VOL. 19; NO 3; PP. 269-278; BIBL. 11 REF.Article

MECHANISM OF SEPARATION OF A LOW-CARBON LOW ALLOY STEEL CONTROL-ROLLED IN AUSTENITE AND FERRITE TWO PHASE REGIONSMATSUDA S; KAWASHIMA Y; SEKIGUCHI S et al.1982; TETSU TO HAGANE; JPN; DA. 1982-03; VOL. 68; NO 3; PP. 435-443; BIBL. 21 REF.Article

Characterization of laser-textured cold-rolled steel sheets = Charakterisierung laser-texturierter kaltgewalzter StahlblecheSNAITH, B; PROBERT, S.D; PEARCE, R et al.Wear. 1986, Vol 109, Num 1-4, pp 87-97, issn 0043-1648Conference Paper

En tchèque = Development of rolling equipments at structural mills = Weiterentwicklung von Walzarmaturen an ProfilstrassenPOLUSHKIN, V.P; IVANOV, J.V.Hutník (Praha). 1987, Vol 37, Num 3, pp 97-103, issn 0438-2757Article

Zum Einsatz von gesinterten Hartmetallwalzringen in Hochleistungsdrahtstrassen = On the use of sintered roll discs from hard metal in high-speed rod millsLIETZMANN, K.D; BOEHLKE, W.Neue Hütte. 1985, Vol 30, Num 11, pp 417-421, issn 0028-3207Article

Maîtrise de l'épaisseur au train à bandes de Sollac Fos après modernisation des cages finisseuses = Thickness control at the Sollac Fos hot strip mill after modernization of the finishing standsSERENA, G.Cahiers d'informations techniques de la revue de métallurgie. 1993, Vol 90, Num 4, IV, VI, VII, 531-535 [8 p.]Conference Paper